Carbon pedals set with illuminated logo Mansory for Rolls-Royce Spectre

Carbon Pedals Set with Illuminated Logo Mansory for Rolls-Royce Spectre

Few interior touches reward the driver of an all-electric Rolls-Royce as quietly as a properly engineered pedal set. The Mansory carbon pedal set with illuminated logo is part of the wider Mansory Carbon Fiber Body kit set for Rolls-Royce Spectre, designed to bring the same hand-laid carbon language found on the exterior into the footwell. On a Spectre, where one-pedal regenerative driving means the right foot rests on the accelerator for the vast majority of every journey, the pedal interface deserves more than a stamped aluminium pad. The Mansory set replaces the OEM rubber-and-metal pads with autoclave-cured carbon faces, machined aluminium cores, hidden-LED illumination of the Mansory wordmark, and grip studs sized for the soft-soled driving shoes Spectre owners typically pair with the car.

Construction & Materials

Each pedal is a sandwich part. A milled 6082-T6 aluminium core handles the load and provides the four threaded mounting holes that align with the OEM pedal armature. A 3K twill carbon shell is laid over the visible face, cured under autoclave pressure, then machined to accept the laser-cut aluminium grip studs and the recessed acrylic logo lens. A hair-thin LED ribbon sits under the lens and is wired through a low-voltage tap shared with the Spectre footwell ambient lighting circuit so the logo brightens with the cabin theme rather than running on a separate switch.

• Weave: 3K twill carbon, 2x2 pattern, top-clear UV-stable lacquer for foot-traffic durability
• Cure: autoclave-pressed at 6 bar, 120 degrees C, full vacuum-bag de-airing before lacquer
• Wall thickness: 2.4 mm carbon shell over a 3.0 mm milled aluminium core
• Pedal-set weight: 612 g for the full three-piece set (accelerator, brake, dead pedal)
• Grip studs: anodised aluminium, 24 per accelerator face, 32 per brake face, machined-radius edges
• Mounting hardware: M5 stainless cap-head bolts into OEM threaded inserts; no drilling, no glue
• Illumination: 0.6 W warm-white LED ribbon, 4-pin connector tapped from the footwell ambient harness
• Finish: deep gloss lacquer over weave; logo lens is clear acrylic with laser-etched Mansory wordmark

Design & Visual Function

The accelerator is the focal pedal of any Spectre footwell because of the way regenerative braking shifts pedal time in an EV. Mansory has tailored the geometry around that fact. The accelerator face is the largest of the three, set at the same OEM pivot angle so heel-and-toe placement does not change, but lengthened by 6 mm at the top edge so the ball of the foot meets carbon rather than carpet on long highway stretches. The grip-stud pattern is densest along the centreline where shoe pressure concentrates and lighter at the edges where the shoe rolls during ankle articulation.

The brake pedal carries a wider grip-stud field because, although used less in one-pedal mode, it must still deliver consistent pedal feel during friction-brake blends and emergency stops. The dead pedal — really a footrest on the left side of the firewall — is finished in matched 3K twill but receives a softer matte clear so it does not flash light upward into the driver's peripheral vision at night. The illuminated wordmark is positioned on the accelerator only, sitting in a 28 x 8 mm acrylic lens that throws a warm halo onto the carbon weave when the door opens or the welcome sequence triggers.

Visually, the set introduces a layered light play unique to the Spectre cabin. Pre-collection silence and the absence of an idling engine mean the driver hears nothing at start-up; the carbon-and-light pedal set gives that quiet a visual companion. The Mansory logo halo dims with the cabin ambient light slider, never glaring, and matches the warm temperature of the Spectre's optional starlight-style headliner.

Compatibility & Fitment

Designed for the Rolls-Royce Spectre (MY2024+, fully electric, twin-motor). Both LHD and RHD pedal layouts are catered for — the accelerator and brake faces are mirrored between the two markets while the dead pedal is symmetrical. The mounting plates are matched to the Architecture of Luxury aluminium spaceframe pedal armature; OEM threaded inserts in the steel pedal levers are used as the structural anchor, so no pedal-arm replacement, no welding, no firewall work is required. The illumination harness uses a shared low-voltage feed from the footwell ambient lighting node and adds no measurable load to the 12 V auxiliary system.

Installation & Reversibility

Installation takes a competent owner around 35 to 45 minutes per car, longer if the harness is being routed cleanly behind the kick panels. Tools needed: 4 mm hex key, T20 Torx, soft-tip pry tool for the lower kick panel, electrical-tape or fabric-loom protection for the LED tap. The OEM rubber pad pulls away from the pedal arm, the Mansory carbon face seats over the same arm with two M5 cap-head bolts torqued to 6 Nm, and the LED pigtail clips into the footwell ambient connector behind the lower trim. Removal is the reverse — every step is reversible and the car returns to OEM-spec without trace, which matters at lease-end and at residual-value time on a Spectre. For owners not comfortable working under the dashboard, any Mansory-trained installer or independent Rolls-Royce specialist will complete the job inside an hour. The acrylic-modified VHB adhesive system used elsewhere on the Spectre's spaceframe is not required here — the pedal set is a fully bolted assembly.

Pairing within the Mansory Spectre programme

The illuminated pedal set is the most theatrical of the two Mansory pedal options for the Spectre and reads best alongside other lit cabin elements. Pair it with the Entrance panels with illuminated logo so that opening the coach doors and stepping in delivers a single coordinated welcome sequence, both sills and accelerator wordmark glowing at the same warm colour temperature. Owners who prefer the carbon footwell language to extend across every panel the driver touches usually add the Carbon trims set across the dash and centre stack, and the Mansory steering wheel so the carbon weave on the rim, the trim panels, and the pedal faces all read as one continuous design line. If the budget points elsewhere, the simpler non-illuminated carbon pedals set with logo shares the same shell geometry without the LED accent.

Maintenance & Durability

The lacquered carbon faces are foot-traffic surfaces and require slightly different care from exterior carbon. Wipe with a microfibre dampened in pH-neutral interior cleaner; avoid solvent wipes, kitchen sprays, and any ammonia-based glass cleaner, all of which dull lacquer and can attack the acrylic logo lens. Grit pressed into the grip studs by shoe soles is the main wear vector — a soft-bristle brush every couple of weeks lifts particles before they polish the anodising. The aluminium grip studs are clear-anodised and will not corrode, but salt residue from winter footwear should be flushed promptly. UV is not a major factor inside a Spectre cabin given the heavily tinted glass, so lacquer fade is minimal; expect a service-free decade if the cleaning regime above is followed. The LED ribbon is rated to 30,000 hours, well beyond the typical lifetime of any cabin trim.

Lead Time & Warranty

Lead time runs 4 to 6 weeks from order, occasionally extending to 8 weeks if the buyer specifies a non-standard logo lens colour or a coloured-thread accent on the dead-pedal edging. The set ships with a 12-month warranty covering manufacturing defects: weave voids, lacquer crazing, LED failure, mounting-hardware corrosion, and stitching where applicable. Wear from normal foot use is excluded, as is damage from incompatible cleaning chemistry — the same caveat that applies to factory Rolls-Royce trim.

FAQ

Q: Will the illuminated logo work with the Spectre's welcome and ambient light sequences?
A: Yes. The harness taps into the footwell ambient lighting node, so the logo brightens during the welcome sequence and dims with the cabin ambient slider rather than running on a separate switch.

Q: Does the changed pedal geometry interfere with one-pedal regen calibration?
A: No. The pivot angle, throw distance, and pedal-position sensor signal are all unchanged because the OEM pedal arm and sensor stay in place. The Mansory part is a face replacement only.

Q: Are LHD and RHD versions different parts?
A: The accelerator and brake faces are mirrored to suit the foot-down pressure pattern in each market. Specify market when ordering. The dead pedal is symmetrical and ships as a single SKU.

Q: Can I retrofit this set if my Spectre already has a non-illuminated Mansory pedal set?
A: Yes. The mounting points are identical between the illuminated and non-illuminated versions, so the swap is a straight bolt-off, bolt-on plus a single low-voltage harness tap.

Q: What happens if a grip stud comes loose?
A: Each stud is individually pressed and lacquer-locked, but if one ever lifts, Mansory supplies a small spares pack with extra studs and adhesive. Re-fitting is a 5-minute job at home.

Specify the carbon pedal set together with the matching entrance panels, steering wheel, and carbon trims set for a fully coordinated Spectre cabin. To configure a specification or check current lead times, contact us via WhatsApp +44 7488 818 747 or [email protected].